Is Your Garage Door Opener Not Working? Here’s What To Do

Garage Door Wall Switch Doesn’t Work

Fix: Replace the wall switch and wires.

If the remote works but the wall switch doesn’t, you may need to replace either the wall switch or the switch wires. To determine whether the garage door opener switch or the wires are bad, first unscrew the switch from the wall and touch the two wires together (don’t worry, the wires are low voltage and won’t shock you). If the opener runs, you have a bad switch.

If you have an older-model opener, a cheap doorbell button might work. If you have a newer opener that has a light and a locking option on the switch, buy the one designed for your model.

If the opener doesn’t run when you touch the wires at the opener, use a small wire and jump those same two wires at the opener terminal. If the opener runs, the wire that connects the opener to the switch is bad. Sometimes the staples that hold the wire to the wall pinch the wire, causing a short. Install 18- to 22-gauge wire as part of the garage door repair.

The Wall Switch Works But the Remote Doesn’t Work

Fix: Replace batteries or buy a new remote or receiver.

If the wall switch works but one of the remotes doesn’t, check the batteries first. Still nothing? You may need a new remote. Home centers carry a few models, and you can find a wide selection online.

If you can’t find one for your garage door opener model, you can try a universal remote or you can install a new receiver. A receiver replaces the radio frequency the opener uses with its own. An added bonus of a new receiver is that it will automatically update older openers to the new rolling code technology, which stops the bad guys from stealing your code. Just plug the new receiver into an outlet close to the opener, and run the two wires provided to the same terminals the wall switch is connected to.

Garage Door Goes Up, But Only Goes Down When You Hold Down the Wall Switch

Fix: Align or replace the safety sensor.

If the door goes up but goes down only when you hold down the wall switch, check to see that the safety sensors are in alignment. The small light on each sensor should be lit up when nothing is between them. Door sensors do go bad, so if no light is showing at all, you may need to replace them. You can save yourself some time by using the existing wires. Also, direct sunlight shining on sensor eyes can make them misbehave.

No Sound or No Lights When You Push the Wall Switch and Remotes

Fix: Replace the circuit board.

If the outlet has power, but there’s no sound or no lights when you push the wall switch and remotes, you probably have a bad circuit board. Lightning strikes are the most frequent reason for the demise of a circuit board. The circuit board consists of the entire plastic housing that holds the lightbulb and wire terminals. The part number should be on the board itself.

Replacing a circuit board sounds like a scary garage door repair, but it’s really quite easy. It will take 10 minutes tops and only requires a 1/4-in. nut driver. Just follow these steps: Remove the light cover, take out the lightbulb, disconnect the switch and safety sensor wires, remove a few screws, unplug the board and you’re done. A circuit board will cost about $80, so make sure you protect your new one with a surge protector. You can buy an individual outlet surge protector at a home center for less than $10.

Everything Works Fine Except the Lights

Fix: Replace the light socket.

If the bulbs are OK but don’t light up, you probably have a bad light socket. To replace the socket, you’ll need to remove the circuit board to get at it. Use the same steps as in ‘Replace the Circuit Board’ (above) to accomplish this.

Once the circuit board is removed, pop out the old socket by depressing the clip that holds it in place. Remove the two wire connections and install the new socket. Replacement sockets cost less than $15.

Be sure to use a bulb of the correct wattage. Using lightbulbs with a higher wattage than the socket is rated for will cause a socket to fail. Not only is this bad for the socket, but it can also be a fire hazard. If your light cover has turned yellow from heat, you’re probably using too strong a bulb.

The Trolley Carriage Moves But Garage Door Doesn’t Open

Fix: Replace the trolley carriage.

If the trolley carriage moves but the door doesn’t open, the culprit is probably a broken trolley carriage. Before you pull the old one off to begin the garage door repair, clamp down the chain to the rail. This will help maintain the location of the chain on the sprocket and speed up reassembly. Once the chain is secure, separate it from both sides of the trolley. Disconnect the rail from the header bracket and move the rail off to one side. Slide off the old trolley, and slide on the new one. Reattach the chain and adjust the chain tension. Replacing the trolley on a belt drive and replacing it on a screw drive are similar procedures. A new trolley will cost $25 to $40 depending on your model.

The Opener Makes a Grinding Noise But the Door Doesn’t Move

Fix: Replace the main gear drive.

If the garage door opener makes a grinding noise but the door doesn’t move, your main drive gear is probably toast. The main drive gear is the plastic gear that comes in direct contact with the worm drive gear on the motor. The main drive gear is the most common component to fail on most openers. Replacing it is a bit more complicated than the other repairs in this article but still well within the wheelhouse of the average DIYer.

There are several components that need to be removed before getting at the gear. Once you get the gear out, you can remove it from the shaft with a punch, or you can buy a kit that comes with a new shaft. Make sure you lube it all up when you’re done. The gear alone should cost you less than $20. A complete kit that comes with the shaft will cost closer to $40.

Garage Door Doesn’t Open

Fix: Lubricate the rail

No matter what type of garage door opener you have, you should always lube the rail where it comes in contact with the trolley carriage. Use a lubricant that doesn’t attract dirt. Silicone spray is a good choice. If you have a screw-drive opener, you’ll need to grease several spots along the rail gear at least once or twice a year. In colder climates, use lithium grease, which won’t harden when the temperature drops. Many home centers sell specifically formulated products near the openers. And don’t use too much or it could drip on your car.

Garage Door Won’t Open All the Way

Fix: Check the chain tension

Most chain drive openers suggest you tighten the chain so there’s about 1/4 in. to 1/2 in. of slack from the rail to the chain (check your manual). Over tightening the chain will put excess wear and tear on the shaft and gears. Too little tension could cause the chain to skip off the sprocket and fall down on your car.

The post Is Your Garage Door Opener Not Working? Here’s What To Do appeared first on Family Handyman.

Article source here: Is Your Garage Door Opener Not Working? Here’s What To Do